I’ve got tons of this sensors. The following codes I have:
- 0A - open
- 0E - closed
- 07 - tamper
- 06 - low battery
I have connected a PIR module (an AM312 - Low current when inactive ~4uA - i did bypass the 3.3v LDO) across the reed switch connections, the STC micro in the WDS07 has a 3.3v feed into Pin 2, which i tapped off, i then re-housed the assembly in a waterproof box, i have placed this down my drive way to detect movement and the RF codes are read by a Sonoff Bridge into Home Assistant and decoded by Node Red - Works excellently and reliably.
2 Likes
Hi, i have a GS-WDS07 Sensor, can you help me with sensor for homeassistant, i receive the code for low battery but how i use it? thanks
hi,
a bit off topic maybe but…I have a couple of this sensor and using a gateway based on EspHome.
Usually to receive door sensors (I also have DIGOO switches) I set the receiver to rc_switch and dump the RF code (format is something like 10100101010) so binary one.
With these GS-WDS07 instead it seems I am not capturing anything: blue led is activating hence I guess it should be transmitting.
How are you doing to capture RF code?
I don’t quite get you.
Do you need help with receiving battery level or you don’t know how to use it in HA?
It would be useful if you could post a relevant bit of your sensor config here.
OMG sends all RF messages to a MQTT topic. Just subscribe to it an check what’s published when your sensor it tripped.
i have a 20 units GS-WDS07 , i wonder i i can convert it to water leak sensor ?
i have this water sensor
i try to soldering 2 wire to the reed but in my test its looks that the short not send the code.
mybe with tamper ? any idea ?
You should measure the impedance of the reed switch and try to replace it with a resistor with the same value first.
If working try to setup a circuit with your water sensor + the resistor or a lower one depending on the total impedance.
This sensor is a total of two pins that connect 2 wires and the water is supposed to shorten between them, I measured between the two REED legs and it gave 3.3V so that means it actually gives the trigger a trigger. The resistor you mean is actually going to simulate the resistance of the REED?
Because I shortened the sensor legs in a glass of water, it actually did nothing.
I am trying to understand the water sensor works whether it is really short or by lowering the resistance following the water.
Yes exactly
I think you should compare the impedance obtainer here with the reed switch one.
I measured the resistance on the REED and it gave me about 50 ohms.
The resistance on both connections after I removed the REED from the board is 1.5M ohms.
I put a 1.5M resistor between the two connections and connected the sensor but it did not help, if I put a resistor over 33K then no contact and still with the sensor is not a short sight to send the RF code.
I don’t really understand it, but I couldn’t really make the sensor a short character like the REED.
Do you have an idea or direction?
If you try to replace the REED with 50 ohms resistor or a close value do you succeed in triggering the sensor?
yes. i try many type of resistor values until 33Kohm . above 33K do nothing.
but with the resistor and the water sensor he do nothings
not 33K, 33ohms only and without the water sensor?
Yes I connected the resistor instead of the 33ohm resistor (I went up in values up to 33K) and it did give a trigger
any idea ?? 
And the resistance of your water sensor when into the water is how much?
sorry cant remember now , i will check it and came back with the answer later
Also could you open a separate topic about this transformation?
ok… i will open new topic
@1technophile Something very interesting about this module is that it comes with a 1.5V AAA battery but if you put a AAA lithium battery it greatly increases its transmission range. It seems that all the modules I had problems with transmitting after replacing the battery started transmitting continuously and quickly…